Dual Beam Moisture Proof Light
Round and Ellipse LED Bulkhead Light with Front and Edge Ring Illumination | SMD2835, PP Housing, Wall and Ceiling Mounted
A surface mounted moisture proof light that emits from two zones at once, a broad front diffuser panel and a bright edge ring around the frame, built on SMD2835 chips with a full PP plastic housing and lens. Available in round and ellipse bodies with black or white frames, for wall or ceiling installation.
Full Specifications
| Shape | Power | Lumens | Size | Materials | Frame Color |
|---|---|---|---|---|---|
| Round | 20W + 20W | 1600 LM | Ø215 x 50mm | PP | Black / White |
| Ellipse | 20W + 20W | 1600 LM | 260 x 140 x 50mm | PP | Black / White |
Product Views
Two Light Zones, One Fixture
Most bulkhead lights emit from a single flat face. This fixture splits its 40W total load into two independent 20W zones so it can light a space from the front, the edge, or both together, depending on how the circuits are wired and switched on site.
Front Panel, 20W
The full diffuser face glows evenly, producing broad, general illumination similar to a standard bulkhead light, suited to filling a corridor or room with usable light.
Edge Ring, 20W
A ring of light runs around the perimeter of the frame, creating a halo effect that reads as a design detail on the wall or ceiling even when the front panel is dim or off.
Why This Fixture Works Well
Independent Circuits
Front panel and edge ring run as separate 20W circuits, so a project can wire them to a single switch for combined light or to separate switches for independent control.
SMD2835 Light Source
A widely used, well proven LED chip package chosen for stable output and consistent color across production batches.
Full PP Construction
Both the housing and the lens are PP plastic, chosen for moisture resistance rather than metal, which can corrode in damp conditions over time.
Two Shapes, One Spec
Round and ellipse bodies share the same 1600LM output and dual 20W circuit design, simplifying planning when a project uses both shapes.
Wall or Ceiling Mounted
The same surface mounted body installs flat against a wall or flush to a ceiling without a separate SKU for each position.
Black or White Frame
Frame color can match the mounting surface for a low profile look, or contrast against it, and the black frame in particular makes the edge ring effect more visually distinct.
Where This Fixture Is Typically Installed
- Hotel corridors and stairwells: Front panel for general illumination, with the edge ring used as a low level night mode.
- Building entrances and lobbies: The black frame with a lit edge ring creates a distinct visual signature at an entry point.
- Balconies and covered walkways: Moisture resistant PP housing suits sheltered exterior locations on either shape.
- Parking structures and carports: Round shape at full front and ring output for maximum coverage in open ceiling areas.
- Bathrooms and utility ceilings: Either shape mounted overhead where a moisture resistant fixture is required.
- Retail and hospitality accent zones: Ellipse shape with the ring circuit run alone as a decorative wall feature.
Frequently Asked Questions
Can the front panel and edge ring be switched independently?
The two zones run as separate 20W circuits. Whether they can be switched independently on-site depends on how the fixture is wired into the local switching setup.
Does using both zones together increase total power draw?
Yes, running the front panel and edge ring together draws the combined 40W total. Running either zone alone draws only that zone’s 20W.
Can this fixture be mounted on both walls and ceilings?
Yes, it is a surface mounted fixture designed to install flat against a wall or flush to a ceiling using the same body.
What is the housing and lens made from?
Both the housing and the lens are PP, polypropylene, chosen for moisture resistance rather than metal or glass components.
Is the round or ellipse shape brighter?
Both shapes share the same 1600LM total output and 20W plus 20W dual circuit design, so brightness is consistent regardless of shape.
Is this fixture suitable for outdoor use?
The PP housing is moisture resistant and suited to damp or sheltered locations. Confirm the specific IP rating with the supplier before specifying it for fully exposed outdoor installation.
Requesting a Quotation or Sample
For MOQ confirmation, FOB pricing, shape or frame color options, or OEM packaging, contact the sales team with your target quantity and destination port.
Reviews
There are no reviews yet.